- Low heat error
– Low temperature error (error code 62)
- Open fuser error (error code 60)
This is main components of fuser unit:
I. How to solve fuser error Samsung ML-2252W.
Whenever fuser unit occurs problems, printing device does not print & all the LEDs turned on & off repeatedly. Gear of the fuser does not operation and breaks away melt away. While printing, motor breaks away from its place due to defective fuser gear.
Now, anyone need to perform the following steps to test. Where is the error? & then meliorate problems
1. Test thermostat, could be AC wire & Heat Lamp is open.After test thermostat, While it is open renew the fuser and try print to test
2. Check the thermistor sensor. If location of the thermistor sensor device is located deep in the sponge, replace thermistor sensor and then print check pages. As soon as still error you must renew the fuser unit.
3. Check the halogen lamp. Check when the circuit of overheat mode works properly. And then renew halogen lamp
4. Test the overheat circuit works properly by DCU with DCU mode is code 10
6. The fuser end of life. Renew fuser unit
II. How to fix(meliorate) low heat error Samsung ML-2252W?
Low heat error is error occur accurrence whenever the temperature of the unit lower than temperature conventional.
The phenomenon of demonstrated Samsung ML-2252W inkjet printer occur error "Low heat error" is:
- The laser printer does not print, the Online/Error LED (red) and the Toner Get LED are turned on and off repeatedly 4 second/ one times.
- The low heat error on the Samsung ML-2252W printer is related to the fusing assembly. Below is a list of the most common troubles that may possibly cause a low heat error.
1. Cycle the turned.
When the lazer printer checks the fuser at the wrong time like during a sudden power outage, it could possibly obtain an inaccurate reading causing this error. Sometimes a simple cycle turned could resolve the issue.
2. Test your company turned source.
Plugged switched cable of printer direct into a wall outlet. Too many devices plugged into the same circuit may also cause a turned struggle between devices & lead to this issue.
3. Follow the diagnostics mode following and check the temperature of the unit when ever it should be hot.
- Remove the fuser unit (review How to remove fuser unit Samsung ML-2252W) and check for continuity across the thermostat & hot roller assembly.
- Test the overall condition of the fuser unit. Any time the hot roller looks extremely worn, the gears are wearing out, or the pressure roller has wrinkles or tears in it, anyone should regenerate the fuser unit Samsung ML-2252W.
4. Remove the thermistor on the fuser unit and clean it off and render sure it is secure against the hot roller.
Debris and also whenever it is positioned to fair away from the hot roller could possibly cause low heat issues. The thermistor is very sensitive and it doesn’t take much to throw it off.
5. The contacts between the electrodes on the sides of the hot roller aren’t making a good connection.
Because this is a metal on metal contact & electricity is running through it, it tends to obtain corrosion in this area. Take an emery board to the surfaces & try to scratch off some of this build up.
6. Any time still error than change the fuser unit.
III. How to fix(mend) Open fuser error Samsung ML-2252W?
The phenomenon of demonstrated Samsung ML-2252W lazer printer occur error "Open fuser error" is: The laser printer does not print, the Online/Error LED (red) & the Toner Down load LED are turned on and off repeatedly 1 second/ one times.
The Open fuser error on these printers is caused by An open-circuit in the fusing assembly.
This error to be one of the more common complications of Samsung ML-2252W printers. Anytime they over heat, one and also both of the thermostats atop the fusing assembly can open. As the fusing unit cools back down the thermostat is supposed to close, anytime the printing device is turned back on it is going to work as normal. However, it does not work properly. The unit cools back down but the thermostat fails to close back up. In this document, i document anyone solve trouble without regenerate fuser unit
1. Take out fuser unit out of frame.
2. take away the fusing assembly and thermostat
3. Test the thermostat, is the continuity across the two parts?.
- Whenever it has continuity then that’s not the problems
- Conversely, measure across the individual thermostats to look for which one is open. If anyone isolate the issues child take a could possibly of air and hold it upside downNow render the front of the thermostat, open in that could possibly be depressed, blowing of extremely cold air then try test the thermostat for continuity once again. As soon as it has continuity now, then reinstall it and put the fuser back in the lazer printer. When the fuser rollers haven’t melted together you actually should have a working lazer printer again.
4. After restore thermostat, the laser printer still error then the difficulties may be in halogen lamp and also connection trouble.
The thermistor the Fuser runs on AC switched so people should have continuity across the halogen lamp & thermostat. Pretty much a plug in path going into & out of the fuser unit. If you’re having an Open fuser error then something in the fuser circuitry is open. It’s up to you actually to get it. Now when you don’t feel like doing all this testing then your own personal next step is to regenerate the fuser unit.
5. Whenever anyone have the fuser out, you actually must check the condition of the unit. Look for scratches in the hot roller surface where the thermistor and pick fingers may possibly have worn away the surface. Test for a warped or wrinkled surface on the pressure roller. Finally check the gears out. Look for gear dust and worn down gear teeth.If there is a difficulties may not be solve, you actually should reaplace Renew Pressure Roller & heat roller
More details, you actually manifestation in "Samsung ML-2252W Service Repair Manual". This guide very important with technician any time restore, disassemble (removable) components the Samsung ML-2252W printing device. "Samsung ML-2252W Service Repair Manual" article technician remove & set up components internal Samsung ML-2252W inkjet printer, providing them knowledge intensive the component, the best way to take apart & mend bugs in the process of using Samsung ML-2252W printing device that the user themselves may not repair.You could fee it at the under:
Costs for Samsung ML-2252W Service Repair Manual: 5$ USTo download Service Repair Manual, pls payment with following info
Paypal : Please comment
